No clutch adjustment?
#1
No clutch adjustment?
Am I correct that the only adjustment that can be made to the SH clutch is the position of the lever? On my SH, it seem that I have to let the clutch out about 50% before it engages and the friction zone is really small.
On my 96 ACE 1100 (cable clutch), the clutch begins engaging after letting the lever out around 20% and is fully adjustable.
I have checked the clutch fluid and it's where it is supposed to be and I even bled the system to ensure there were no air bubbles. Is this just the nature of this clutch?
Thanks!
Retro
On my 96 ACE 1100 (cable clutch), the clutch begins engaging after letting the lever out around 20% and is fully adjustable.
I have checked the clutch fluid and it's where it is supposed to be and I even bled the system to ensure there were no air bubbles. Is this just the nature of this clutch?
Thanks!
Retro
#3
Re: No clutch adjustment?
Yes. There is a small black wheel at the back of the clutch lever that has four (if I remember correctly) settings. Turn all the way in to the right for the closest to you.
Ride safe!
Retro
Ride safe!
Retro
#6
Re: No clutch adjustment?
Mine is the same. I even bought some clutch plates as I too thought it was about warn out but then I let a very experienced honda rider (former mechanic etc) who said it felt like a regular honda hydraulic clutch, i.e., too much free play. Dunno......
#7
Another area to consider it the metal spacer that is found behind the primary sprocket cover (between the cover and the engine case). I installed my Coerce sprocket cover/guard (eliiminates the stock big black cover) before a trackday and forgot to put in that spacer. When I fired the bike up, plunked it into 1st and then let out the clutch, NOTHING HAPPENDED!!! I was like, WTF! Without that spacer in there, the clutch piston was still pushing on the rod just enough to keep the clutch disengaged.
I quickly pulled off the aluminum guard and put in washers on each mounting bolt, sandwiched between the guard and the crankcase. Bingo, problem solved.
So to make a long story longer, I'm guessing that different thicknesses of washers may affect the engagement point of the clutch. Pretty easy to play with at least.
I quickly pulled off the aluminum guard and put in washers on each mounting bolt, sandwiched between the guard and the crankcase. Bingo, problem solved.
So to make a long story longer, I'm guessing that different thicknesses of washers may affect the engagement point of the clutch. Pretty easy to play with at least.
#10
Re: No clutch adjustment?
#12
Yes, a smaller diameter piston would be the answer to getting a wider friction zone for sure - or somehow altering the leverage of the whole thing...
#13
My clutch disengages when I pull the lever about 15% of the way. It also has a low pitched squeal when I slip it under moderate power. The bike is new to me with about 9500 mi. I'm thinking the clutch is toast. Seems like low mileage to have a fried clutch (without knowing what the last guy did to it). I'm going to experiment today to see if it will slip in high gear under power.
I was looking at parts to replace the clutch. Do I just need the three clutches and the two plates to do the job? I've done car clutches before but not cycle. Am I opening a can of worms? I have an image of me standing in the driveway coated in oil, surrounded by springs!
I was looking at parts to replace the clutch. Do I just need the three clutches and the two plates to do the job? I've done car clutches before but not cycle. Am I opening a can of worms? I have an image of me standing in the driveway coated in oil, surrounded by springs!
#14
Holy reincarnation, Batman!!!! Did you see how old this post is?
The noise is normal. The VTR doesn't like high rpm clutch slips. The clutch should not slip under full power 4th gear...or any gear for that matter. If it does that means it's time to replace it. The lever travel (15%) is normal too.
The noise is normal. The VTR doesn't like high rpm clutch slips. The clutch should not slip under full power 4th gear...or any gear for that matter. If it does that means it's time to replace it. The lever travel (15%) is normal too.
#15
I've seen your rants about people not searching old threads. Don't want to get anyone fired up!! Besides, I didn't think anyone would mind me hijacking this old dinosaur.
That's good news though. Most bike i've ridden have a clutch that's in the friction zone somewhere in the middle, not right at the first hint of a grab. I'll check the 4th gear power situation. Thanks
That's good news though. Most bike i've ridden have a clutch that's in the friction zone somewhere in the middle, not right at the first hint of a grab. I'll check the 4th gear power situation. Thanks
Thread
Thread Starter
Forum
Replies
Last Post