Will these Flushmounts fit on my hawk?
Thread Starter
Banned
Back Marker
Joined: Jul 2005
Posts: 151
From: Wolverines A pussy
Will these Flushmounts fit on my hawk?
I am upgrading to flushmounts and was just curious if these will fit my hawk?
Anyone using these?
http://www.chaparral-racing.com/Prod...L122-9700.aspx
Thanks!
Anyone using these?
http://www.chaparral-racing.com/Prod...L122-9700.aspx
Thanks!
Senior Member
SuperBike
Joined: Aug 2009
Posts: 1,978
From: thorold ontario
those look like the ones i have, i bought a set for a cbr 600, like 8541 said you need to make some plates, i used some pl premium and stuck them on like that and let them sit over night.
Senior Member
Superstock
Joined: Oct 2009
Posts: 250
From: NJ/NYC
I am putting mine on tomorrow because I just bought a set and waiting for the LED lights to put in them.
My question about putting these in, when the originals came out they were secured on the inside plastic pieces. Do you still need to secure those or do you just take them out? They don't seem to have a reason to be there, just to hold on the OEM lights.
My question about putting these in, when the originals came out they were secured on the inside plastic pieces. Do you still need to secure those or do you just take them out? They don't seem to have a reason to be there, just to hold on the OEM lights.
Thread Starter
Banned
Back Marker
Joined: Jul 2005
Posts: 151
From: Wolverines A pussy
Yeah im not 100% sure but im sure ill be fabricating a lot. I ordered an LED tail light with integrated turn signals and will be changing the undertail assembly to accept an undertail exhaust.. Pretty excited about the coming months. Going to be a lot of work but should be where i want it by December.
Banned
MotoGP
Joined: Aug 2007
Posts: 5,942
From: Lake View Terrace, CA
I am putting mine on tomorrow because I just bought a set and waiting for the LED lights to put in them.
My question about putting these in, when the originals came out they were secured on the inside plastic pieces. Do you still need to secure those or do you just take them out? They don't seem to have a reason to be there, just to hold on the OEM lights.
My question about putting these in, when the originals came out they were secured on the inside plastic pieces. Do you still need to secure those or do you just take them out? They don't seem to have a reason to be there, just to hold on the OEM lights.
Senior Member
Superstock
Joined: Oct 2009
Posts: 250
From: NJ/NYC
RUNLEVELZERO #99
SuperBike
Joined: Jan 2007
Posts: 2,219
From: Skokie
Yes they will fit fine but be sure to order the 3-wire (so the running light & TS function) LP Type 3 with amber lens' . I used double-sided foam tape for a tight fit between the fairing & units and cut a thin aluminum piece with lock washers & nuts for the back side. Oh, and buy extra bulbs which are only available from LP.
Last edited by skokievtr; Oct 18, 2010 at 01:59 PM.
Senior Member
Superstock
Joined: Oct 2009
Posts: 250
From: NJ/NYC
they have an LED kit for them too, if you want to get noticed a bit more.
This is what I have on order:
http://www.customled.com/products/fl...flushmount.htm
This is what I have on order:
http://www.customled.com/products/fl...flushmount.htm
Thread Starter
Banned
Back Marker
Joined: Jul 2005
Posts: 151
From: Wolverines A pussy
Ok got the turn signals in and they deffinitely wont fit... Way to big.. Guess i should have read the size of them.. Any other sites with flushmount turn signals that will actually fit?
the boss
SuperBike
SuperBike
Joined: Mar 2010
Posts: 1,182
From: largo,fl
have you thought about doing protons,i put protons on my bike and its dam near perfect fit,its the protons for the rc51,they are led,they run correctly if you get the led flashers and you good to go.
Thread
Thread Starter
Forum
Replies
Last Post
