clutch play
Thread Starter
Jack of all Master of non
Superstock
Joined: May 2011
Posts: 297
From: Jacksonville,fl
clutch play
Here is the noise and play. In my clutch
‪Vtr 1000 clutch slop‬‏ - YouTube
‪Vtr 1000 clutch slop‬‏ - YouTube
Last edited by 3amta3; Jul 18, 2011 at 03:38 PM.
Thread Starter
Jack of all Master of non
Superstock
Joined: May 2011
Posts: 297
From: Jacksonville,fl
the only other thing i have is the starter gear.... the one with the shaft going through it, it moves side to side on the shaftabout 5 mm or so almost like there is a shim missing or something.... every thing else checks out goood IAW the specs. i had some really thin and long metal shavings in the oil, not sure where they came from but look almost like plating foe gears
Banned
MotoGP
Joined: Aug 2007
Posts: 5,942
From: Lake View Terrace, CA
the only other thing i have is the starter gear.... the one with the shaft going through it, it moves side to side on the shaftabout 5 mm or so almost like there is a shim missing or something.... every thing else checks out goood IAW the specs. i had some really thin and long metal shavings in the oil, not sure where they came from but look almost like plating foe gears
The metal shavings sound pretty normal also as it is some casting flash the was caught by the oil pump screen. I would say most, if not all SH's will have this if the oil pan has never been removed and it is not something to worry about.
Thread Starter
Jack of all Master of non
Superstock
Joined: May 2011
Posts: 297
From: Jacksonville,fl
the clatter on acceleration is what i am trying to find. but nothing seams to be out of the ordinary. i did change the water pump chain because it was worse than the oil pump chain. if the carbs are not synced right will that cause the clattering noise in the lower end? i dont know what else to look at??????????????????????????????????
Senior Member
MotoGP
Joined: Mar 2007
Posts: 3,132
From: Phoenix, AZ
Carb slides are somewhat noisy, and don't hurt anything.. CCTs are a remote possibility..
edit: If it is very loud, my guess is actually the drive chain. I chased that one for a while before I figured it out.
edit: If it is very loud, my guess is actually the drive chain. I chased that one for a while before I figured it out.
Thread Starter
Jack of all Master of non
Superstock
Joined: May 2011
Posts: 297
From: Jacksonville,fl
cct's have been changed out. that was the original noise problem but that was fixed and then this new noise.. i have tightened my drive chain but i did find that it could use to be cleaned or even changed out...
the noise is in the front bottom left end of the bike.....
here is what i have done/changed
1. cct r/r
2. changed water pump chain
3. cleaned a very dirty clutch slave cylinder and replaced seal
4. checked all valve clearances
5. checked sprag clutch
6. starter gears
7. blocked and sealed off chokes
8. removed the pair system
9. checked clutch plates(all good)
maybe changing the drive chain
not sure what else to check or change...i have 60k miles on this, anyone have any precautionary things that should be changed
the noise is in the front bottom left end of the bike.....
here is what i have done/changed
1. cct r/r
2. changed water pump chain
3. cleaned a very dirty clutch slave cylinder and replaced seal
4. checked all valve clearances
5. checked sprag clutch
6. starter gears
7. blocked and sealed off chokes
8. removed the pair system
9. checked clutch plates(all good)
maybe changing the drive chain
not sure what else to check or change...i have 60k miles on this, anyone have any precautionary things that should be changed
Thread Starter
Jack of all Master of non
Superstock
Joined: May 2011
Posts: 297
From: Jacksonville,fl
it is dirty and when you kink it up it holds the kink.. i think it is just dirty but i am going to clean it tomorrow and find out if it will loosen up any, if not i will be replacing it. the slack was taken up as it was hitting the exhaust ] i am also changing the cush drive once the parts come in.
Banned
MotoGP
Joined: Aug 2007
Posts: 5,942
From: Lake View Terrace, CA
it is dirty and when you kink it up it holds the kink.. i think it is just dirty but i am going to clean it tomorrow and find out if it will loosen up any, if not i will be replacing it. the slack was taken up as it was hitting the exhaust ] i am also changing the cush drive once the parts come in.
Thread Starter
Jack of all Master of non
Superstock
Joined: May 2011
Posts: 297
From: Jacksonville,fl
i think i am going to change it out anyways but i figure i could clean it and see how it turns out..... how would that give me my noise though, it is not making sense to me how that would give me engine noise?????
Banned
MotoGP
Joined: Aug 2007
Posts: 5,942
From: Lake View Terrace, CA
As it passes over the drive sprocket the noise could sound like it was coming from the engine but then again trying to diagnose a noise over the internet is rather difficult at best so I can only give you my best guess.
Thread
Thread Starter
Forum
Replies
Last Post
