SuperHawk Forum

Modifications - Cosmetic Discuss aftermarket and DIY cosmetic modifications

Melted Flush Turn Signals

Thread Tools
 
Search this Thread
 
Old May 22, 2007 | 06:23 AM
Share
  #1  
spdrcr's Avatar
spdrcr
Thread Starter
Senior Member
Back Marker
 
Joined: May 2007
Posts: 227
From: Arnold Missouri
spdrcr is on a distinguished road
Melted Flush Turn Signals
I installed some flush signals (I think they are EMGO?) last week. This morning while warming up the bike I noticed they were loose and tried to tighten them and they just pulled out stetching about 4" long . Maybe I should have hooked them up for two wire opperation?
Reply
Old May 22, 2007 | 07:38 AM
Share
  #2  
SPRHK's Avatar
SPRHK
my e-penis is huge!!
Superstock
Superstock
 
Joined: Sep 2005
Posts: 257
From: belvidere nj
SPRHK is an unknown quantity at this point
They worked fine all along?
Reply
Old May 22, 2007 | 07:39 AM
Share
  #3  
SPRHK's Avatar
SPRHK
my e-penis is huge!!
Superstock
Superstock
 
Joined: Sep 2005
Posts: 257
From: belvidere nj
SPRHK is an unknown quantity at this point
Sounds like something short curcuited inside.
Reply
Old May 22, 2007 | 08:01 AM
Share
  #4  
superbling's Avatar
superbling
Moderator
MotoGP
 
Joined: Dec 2004
Posts: 2,553
From: South Texas
superbling is on a distinguished road
Pics would be good.
Reply
Old May 22, 2007 | 08:02 AM
Share
  #5  
spdrcr's Avatar
spdrcr
Thread Starter
Senior Member
Back Marker
 
Joined: May 2007
Posts: 227
From: Arnold Missouri
spdrcr is on a distinguished road
They still work but I have them hooked up as running lights and turn signals. I guess they couldn't handle the heat of the lamp on all the time.
Reply
Old May 22, 2007 | 08:05 AM
Share
  #6  
superbling's Avatar
superbling
Moderator
MotoGP
 
Joined: Dec 2004
Posts: 2,553
From: South Texas
superbling is on a distinguished road
Was this a mod or were they designed as a running light model.
Reply
Old May 22, 2007 | 08:32 AM
Share
  #7  
spdrcr's Avatar
spdrcr
Thread Starter
Senior Member
Back Marker
 
Joined: May 2007
Posts: 227
From: Arnold Missouri
spdrcr is on a distinguished road
It's a three wire turn signal. On, flash & ground.
Reply
Old May 22, 2007 | 08:44 AM
Share
  #8  
SuperLoud's Avatar
SuperLoud
Member
Squid
 
Joined: Aug 2005
Posts: 74
From: SW Missouri
SuperLoud
If I remember right the turn signal bulb is much brighter than the running light .
Sounds like you have the wires switched so that the turn signal is running all the time which made it too hot and melt.
Reply
Old May 22, 2007 | 09:19 AM
Share
  #9  
spdrcr's Avatar
spdrcr
Thread Starter
Senior Member
Back Marker
 
Joined: May 2007
Posts: 227
From: Arnold Missouri
spdrcr is on a distinguished road
Here's a pic.
Reply
Old May 22, 2007 | 09:48 AM
Share
  #10  
Shmittay's Avatar
Shmittay
Senior Member
Back Marker
 
Joined: Jul 2004
Posts: 159
From: Northern VA
Shmittay
Originally Posted by SuperLoud
If I remember right the turn signal bulb is much brighter than the running light .
Sounds like you have the wires switched so that the turn signal is running all the time which made it too hot and melt.
Exactly what i was thinking. I did something similar when I put flush mounts on my F3.
Reply
Old May 22, 2007 | 02:22 PM
Share
  #11  
Randman's Avatar
Randman
Moderate-whore
MotoGP
 
Joined: Nov 2005
Posts: 9,052
From: Leander TX!!
Randman is on a distinguished road
Originally Posted by spdrcr
Here's a pic.
Maybe the kid switched the wires on you...Mine have done that before, I mean who else you gonna blame, not like I did....That's my story
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Stock cans, turn signals, horn and aftermarket turn signals and more...
Magnus
Classifieds
5
May 29, 2014 06:52 PM
Flush mount turn signals / Integrated turn signals in mirrors- question about both
johnclopp85
Technical Discussion
5
May 13, 2009 07:20 AM
My flush mounts melted....
drew_c14
Technical Discussion
12
Jan 8, 2008 05:58 PM
WTT:Front turn signals amber for clear (flush style non led)
iamanonymous
Classifieds
2
Sep 5, 2006 12:56 PM
Cool semi flush mount turn signals - will they work on a VTR
CNI Dawg
Modifications - Cosmetic
1
Nov 7, 2005 10:37 AM
Tags
Back to Subforum
Modifications - Cosmetic
View Next Unread
MIG exhaust




Advanced Search

All times are GMT -7. The time now is 10:02 PM.