two brothers slip ons
#1
two brothers slip ons
i recently bought some parts for my hawk and the box had some slip on muffers in it ,along with the stuff that i wanted.the guy said they were for a superhawk.i got home and they are TBR mufflers with the passenger peg brackets, but no mid pipes.the pass peg bracket holes line up with the holes on my bike.i have no use for the mufflers or the pass peg brackets.the parts do have some wear and tear and some road rash on the pegs.they do have the two hangers but no other hardware.i want to see if theres any interest here, before i put them on ebay.again i cant be sure they will fit a superhawk.$100.00 shipped,obo superhawk pictures by yamahadm250 - Photobucket SOLD SALE PENDING
Last edited by yamahadm250; 05-24-2011 at 06:06 PM.
#7
I have a set of SS2r slip on low pipes that I want to replace. If these will fit on my exsiting mid pipes. I will purchase these. Any ideas anyone. What are the size of the pipes where the mid pipes go into.
#8
i`ll see if i can get some measurements and post them tomorrow.
here`s the measurements, hope this helps
can length= 15"
inlet length= 2 1/4"
inlet dia. outside =2 3/16"
inlet dia inside= 2"
exit length= 2 1/2"
can are round dia, 14 1/2"
here`s the measurements, hope this helps
can length= 15"
inlet length= 2 1/4"
inlet dia. outside =2 3/16"
inlet dia inside= 2"
exit length= 2 1/2"
can are round dia, 14 1/2"
Last edited by yamahadm250; 05-24-2011 at 04:41 PM.
#15
I just put the exhaust on 1 hr ago and it sounds great! I had a problem at first, because of my error in measurments. The mid pipe was the same diameter, therefore it would not fit. I took it to a friend of mine at a muffler shop and he was able to expand the diameter of the intake on the cannister. I did not think he would be able to do it, because if the aluminum casting it was made of, but he was able to. I now have to get exhaust springs, because the ones I had on the SS2r's are too short. Thank you for the great deal Derral!
PS if any one is intrested in the brackets, they are for hi mount pipes, I will sell them for $25.00 plus shipping OBO. I also will sell the SS2r cannisters (w/out mid pipes), that are bebaffled and shortened by approx. 4-5" and in rough shape (both end pieces are in decent shape) i would sell them for $20.00 plus shipping OBO.
PS if any one is intrested in the brackets, they are for hi mount pipes, I will sell them for $25.00 plus shipping OBO. I also will sell the SS2r cannisters (w/out mid pipes), that are bebaffled and shortened by approx. 4-5" and in rough shape (both end pieces are in decent shape) i would sell them for $20.00 plus shipping OBO.
Last edited by sethday; 06-08-2011 at 04:51 PM. Reason: ...
#16
I just put the exhaust on 1 hr ago and it sounds great! I had a problem at first, because of my error in measurments. The mid pipe was the same diameter, therefore it would not fit. I took it to a friend of mine at a muffler shop and he was able to expand the diameter of the intake on the cannister. I did not think he would be able to do it, because if the aluminum casting it was made of, but he was able to. I now have to get exhaust springs, because the ones I had on the SS2r's are too short. Thank you for the great deal Derral!
PS if any one is intrested in the brackets, they are for hi mount pipes, I will sell them for $25.00 plus shipping OBO. I also will sell the SS2r cannisters (w/out mid pipes), that are bebaffled and shortened by approx. 4-5" and in rough shape (both end pieces are in decent shape) i would sell them for $20.00 plus shipping OBO.
PS if any one is intrested in the brackets, they are for hi mount pipes, I will sell them for $25.00 plus shipping OBO. I also will sell the SS2r cannisters (w/out mid pipes), that are bebaffled and shortened by approx. 4-5" and in rough shape (both end pieces are in decent shape) i would sell them for $20.00 plus shipping OBO.
Thread
Thread Starter
Forum
Replies
Last Post