Rear sets - anyone used these?
02-15-2010, 10:56 AM
#1
Senior Member
Back Marker
Thread Starter
Join Date: Mar 2008
Location: Massachusetts
Posts: 229
Rear sets - anyone used these?
Before I waste time chasing these, has anyone used these rear sets?
http://www.motolanna.com/ourshop/pro...P2-Silver.html
http://www.motolanna.com/ourshop/pro...P2-Silver.html
02-15-2010, 11:40 AM
#6
Senior Member
Back Marker
Thread Starter
Join Date: Mar 2008
Location: Massachusetts
Posts: 229
Umm. Now that you mention it...
I looked into the Cycle Pirates adjustable peg solution but wasn't sold on the idea. I was looking for something a bit more affordable that the Gillies, etc. I don't have the spare time to prowl Ebay waiting for a set of real reasets to come up.
Thanks for the info. Guess I'll keep looking.
I looked into the Cycle Pirates adjustable peg solution but wasn't sold on the idea. I was looking for something a bit more affordable that the Gillies, etc. I don't have the spare time to prowl Ebay waiting for a set of real reasets to come up.
Thanks for the info. Guess I'll keep looking.
02-15-2010, 02:15 PM
#9
Senior Member
SuperBike
Join Date: Feb 2007
Location: Portland, Oregon
Posts: 1,051
02-16-2010, 01:07 AM
#12
Out of my mind, back in 5
MotoGP
Join Date: Nov 2006
Location: Skurup, Sweden
Posts: 6,109
Those are the very same one's that I have on my bike, minus the black anodizing... (I choose the CBR1000RR one's)...
The bearings they come with are utter crap, not sealed, but once you replace those, the rest of the work is quite nice...
02-16-2010, 04:39 AM
#13
Senior Member
SuperBike
Join Date: Nov 2007
Location: Westerly, RI
Posts: 1,216
A little confusing here. Which ones work. The ones in the original post? The same company as the original post but the 1000RR rearsets?
02-16-2010, 06:45 AM
#15
Senior Member
Superstock
Join Date: Oct 2009
Location: Concord, NC
Posts: 344
My rearsets only cost me 2 bucks and a little time. I got a piece of 1x1/8 stock aluminum from Lowes, cut off a 1 1/2 inch piece, drilled holes in each end, then removed the lower bolt from the stock pegs, swung the entire setup to the rear a little bit, then used the piece of aluminum as a spacer. This effectively moved my footpegs back and up about 1 inch each. Why spend big bucks when a few dollars and a little time is all it takes. 
02-16-2010, 08:12 AM
#17
COBB Member
Superstock
Join Date: Jul 2009
Location: NorthEast Connecticut
Posts: 292
rearsets
02-16-2010, 08:25 AM
#18
Senior Member
SuperBike
Join Date: Nov 2007
Location: Westerly, RI
Posts: 1,216
02-16-2010, 09:14 AM
#19
Out of my mind, back in 5
MotoGP
Join Date: Nov 2006
Location: Skurup, Sweden
Posts: 6,109
I have the dimensions and a couple of paper templates... Somewhere... I'll go look...
02-16-2010, 09:38 AM
#21
Out of my mind, back in 5
MotoGP
Join Date: Nov 2006
Location: Skurup, Sweden
Posts: 6,109
I can't fin any of the Robby Moto one's that are adjustable... Just a fixed set with the pegs raised and moved back... Same for Coerce...
Is that all you guy's want, take a plate like mine and add the OEM rearset from a CBR929RR and you are set... Drill the holes where you like...
Is that all you guy's want, take a plate like mine and add the OEM rearset from a CBR929RR and you are set... Drill the holes where you like...
02-17-2010, 04:20 AM
#22
Senior Member
SuperBike
Join Date: Nov 2007
Location: Westerly, RI
Posts: 1,216
Thanks again Tweety.
02-17-2010, 06:33 AM
#24
COBB Member
Superstock
Join Date: Jul 2009
Location: NorthEast Connecticut
Posts: 292
02-18-2010, 06:29 AM
#27
Senior Member
Superstock
Join Date: Oct 2009
Location: Concord, NC
Posts: 344
Not my idea...I stole it from Nathan here on the forum. MUCH cheaper. 
Maybe I should start manufacturing them for 20 bucks a set.
In all honesty, I'd be happy to make a few crude sets and mail them out if anyone wants them. I have some left over aluminum stock and a drill press in the garage.
Maybe I should start manufacturing them for 20 bucks a set.
In all honesty, I'd be happy to make a few crude sets and mail them out if anyone wants them. I have some left over aluminum stock and a drill press in the garage.
Last edited by NCDave; 02-18-2010 at 06:33 AM.
02-18-2010, 05:35 PM
#28
Senior Member
Back Marker
Join Date: Nov 2007
Location: tx
Posts: 238
r/sets
05-02-2010, 03:17 PM
#29
Junior Member
Squid
Join Date: Mar 2009
Location: Maine
Posts: 12
Nice to see some options... I am going to mock up something in Mastercam that looks like tweety's adapter and sick the Excel on some 1/2" plate. Should have thought of that before I spent 3 hours tig'in the LH peg back on.
05-02-2010, 05:42 PM
#30
Senior Member
MotoGP
Join Date: Aug 2006
Location: altoona, pa
Posts: 2,934
yeah. thanks for the acknowledgement and i learned it from another forum, another honda, and it sets your feet essentially even with the top of the swingarm> so about an inch rearward and an 1.5" upward. What's really good is it costs nothing and is easily reversible if you decide you don't like it. A win win IMO. Just be sure you to drill the pieces that move it rearward the same so both sides will be equal. I love em and if you drag these, you will be horizontal shortly thereafter. Adjustables may give you more options, i guess.
