Parting out 99 SH
 

EVERYTHING IS SOLD!!!

MOVING SALE! Get this stuff out of my garage before it goes to the dump!

I live in Alameda Ca 94501



All prices are negotiable. FEEL FREE TO MAKE OFFERS! Makes this a LOT easier!

I also have a stock set of wheels w/o tires. White with machined lip. $140+shipping PRICE DROP
Frame- $180
swing arm- $50
Engine, 25,500 miles on it - $500obo PRICE DROP!


pick up the rest of the bike, motor/tranny/frame/subframe/swingarm and several more parts for $975 OBO!!!

Cash talks...

Are those Dymag wheels available?

Uh... about that... the rear one is cherry! With a diabo III still mounted with good life left. The front... not so much. The front one shattered when I side swipped the wall.

I did speak to another CF wheel maker, and they offered me a deal to trade them the old rims (yes, the broke one too) and they would give me a new set for around half price. If interested, I will find that email for you.

Like to be in line for the Ohlins shock...

Consider yourself 1st in line.

i could use left, right, & center fairings, fairing stay, and clutch reservoir (or whole clutch master w/ reservoir). are the pipes lo or high?

How much for the wheel set as I might not even need the front if I pull the trigger on a CBR front end?

The pipes are the low mount with a little bit of rash but barely noticable.
I have the fairing stay, Im pretty sure its straight Ill double check when I get home. As for the fairings all of them are cracked, shattered or gone. I have the full lower with a crack, and the seat cowl (good cond) but all the rest is beyond repair.
clutch reservoir set up is good, just let me know how much of it you want or need.

New set of CF wheels runs anywhere from $2000-3500 depending what you get. I was asking $900 for the rear with the Diablo III still mounted.

2nd for the rear shock if the 1st falls through please!

noted!

I have a 98 model, I'm pretty sure the stator off yours will fit mine. Do you still have that? And the wire harness from underneath the seat

Im pretty sure it will too. And I have all of the wiring. What do you mean just the wiring underneath the seat? Isnt the wiring harness all one piece?

I checked but you may want to double check. The stator is the same part number for both 98 and 99.

New stator at bike bandit is $304.24, Im obviously not looking for that! Make an offer.

What price on the Scotts? With mounting then of course? Regardless I'm first in line...;)

This is why I dont like people PM'ing asking for parts and prices. Two people asked about the scotts at the same time.

Please ask in the thread, THEN we can finalize via PM. then I am not having to repeat everything for each PM. I can answer questions in the thread for EVERYONE to see.

The guy who PM'ed me beat you by 4 mins. inderocker has dibs. but youre second!

No problem... I'll take seconds...;) I'm still not convinced I need one... But the tinkerer in me want's one just the same...

Its a good upgrade, pricey but def worth it.
These bike are a little heavy in the corners and sometimes a bumb can get them squirrely. I liked having it installed, I just need the money really badly.

PMed about the clutch cover

Is the RH side clutch cover rashed at all?

Slightly, my leg took the brunt of the rubbing on the rock wall. :cry: ill take pictures when I get home.

OUCH.. how fast where you going? I will be on here in a bit to check it out.
Thanks

There is a (bad) picture of the right side of the bike I posted in this thread already. you cant see the rash because its that small.

I was only going about 30-40 but about 25 when I finally hit. I knew I was gonna swipe so I started to jump off.

Nice.. so your fine?

Couple broken bones in my hand, surgery and a cast later with some physical therapy Im ok. I can ride again, thats all that matters :D

pm sent

Replied

I think I see some bar ends on there, this may sound strange, but I would like to get a hold of the bolts and plugs for the bar ends. I picked up a brand new set of bar ends on here but minus the hardware. I currently have 1 bar end on mine with the bolt and plug but I am missing the right side completely (bar end, bolt, plug and all). Just need the hardware.

How does a bazillion dollars sound?
Or just your address and $10 shipped? Ill let you pick, but I could use the bazillion dollars...

Seat cowl is black, correct? Still available?

The seat cowl was blue and black marble. but got scuffed so I sanded down to primer and rattle canned black. Not a pro job but looks decent. I was using it as a test piece for when I painted the entire bike for the track.

And yes, its avail.

I've got about 3 rattle cans of factory black anyhow... How much shipped?

PM sent Pop

Exhaust
 

Would you be willing to trade the exhaust for a set of aluminum SS2R shortened and debaffled and some cash?

pm replied. also might be interested in chain and sprockets... have some jeep stuff stashed in the garage if you may be willing to do trade. I'll be down in Modesto area for Thanksgiving and could cruise into the bay... save us both on shipping.

pm replied.

I'll get in line for the clutch cover if it becomes available

what full lower fairing do you have

Sorry, but my other superhawk has a staintune exhaust and is loud as hell. I like it and dont have a need for another exhaust.

Sounds good about meeting up, sold the Jeep already, and someone has dibs on the sprockets but Ill keep you posted. Its stock 16-43 and I also have a 43 tooth aluminum sprocket $25.

I have the chin fairing on my 98 and the full coverage one from my 99. I took it off soon after buying the bike since I was in Hawaii and it was always overheating sitting in traffic.

you dont know what brand the full one is, i have a full one but looking for a bigger one like sharkskinz, maybe a pic of it,thanks

Bar ends and hardware are sold!